Дисплей MKS 12864 Oled 1.3 дюйма

В наличии: 2 шт.

1849 р.

Артикул: 3D-MKS12864OLED1.3

Описание

MKS 12864OLED adopts OLED display with excellent display effect ,
and is created by Makebase.
It is suitable for the printer which carries with small display ,mini installed size .

Shipping list:
1pcs*MKS 12864 OLED1.3
2pcs*cable

Features
1. Default 1.3 inch OLED display;
2. The interface is as the same as 2004/12864LCD.
3.Support SD card

Notice:
1. Need to adjust Marlin config before use, please refer to the below usage instructions.
2. If you are competent to create a Repetier, that will work with this mini display.
( or else Repetier is not available)
3. We can provide firmware for testing, but technical support is not available.

Please follow the connection sequence, especially 3v3 and GND,
wrong connection will burn OLED.
GND: connects to GND of OLED power ground
3V3: VCC of OLED power anode
CLK: CLK of OLED clock
MOSI: MOSI of OLED data
RES: RES of OLED reset
DC: DC of OLED data order option
CS: CS of OLED chip selection

Instruction on Usage
1. If use Arduino IDE, We suggest V1.5.4 updated version.
Then unzip U8glib.rar into libraries directory. As follow:
Please visit our Github to download firmware.
github.com/makerbase-mks

2. Add following parameters on '' Configuration.h''.
/*---------------MKS OLED patch_1-----------------------*/
// MKS OLED 1.3'' 128x64 FULL GRAPHICS CONTROLLER
#define MKS_OLED13_128x64_FULL_GRAPHICS_CONTROLLER
#if defined (MKS_OLED13_128x64_FULL_GRAPHICS_CONTROLLER)
#define DOGLCD
#define U8GLIB_SH1106
#define REPRAP_DISCOUNT_SMART_CONTROLLER
#define NEWPANEL
#endif
/*---------------MKS OLED patch_1-----------------------*/

3.Add following parameters on '' dogm_lcd_implementation.h''.
/*---------------MKS OLED patch_2-----------------------*/
#elif defined(U8GLIB_SH1106)
U8GLIB_SH1106_128X64 u8g(23, 17, 16, 25); // SW SPI Com: SCK = 23,
MOSI = 17, CS = 16, A0 = 25
/*---------------MKS OLED patch_2-----------------------*/

4. Add following parameters on '' Marlin_main.cpp''.
/*---------------MKS OLED patch_3-----------------------*/
#if defined (MKS_OLED13_128x64_FULL_GRAPHICS_CONTROLLER)
pinMode(LCD_PINS_DC, OUTPUT);
pinMode(LCD_PINS_RST, OUTPUT);
digitalWrite(LCD_PINS_RST , LOW);
delay(1000);
digitalWrite(LCD_PINS_RST , HIGH);
#endif
/*---------------MKS OLED patch_3-----------------------*/

5.Add following parameters on '' pins.h''.
/*---------------MKS OLED patch_4-----------------------*/
#if defined (MKS_OLED13_128x64_FULL_GRAPHICS_CONTROLLER)
#ifdef LCD_PINS_D5
#undef LCD_PINS_D5
#define LCD_PINS_D5 -1
#endif
#ifdef LCD_PINS_D6
#undef LCD_PINS_D6
#define LCD_PINS_D6 -1
#endif
#define LCD_PINS_RST 27
#define LCD_PINS_DC 25
#endif
/*---------------MKS OLED patch_4-----------------------*/

Характеристики товара

Доставка

Оплата

Поделиться

Отзывы

Отзывов пока нет. Ваш будет первым.

Ваш отзыв успешно отправлен на модерацию и будет размещен в ближайшее время

Пожалуйста, нажмите "Я не робот"

Оставить отзыв

Корзина (0)

Корзина

Оформить заказ

Закрыть